Hey everyone, I’m Sam, and I’ve been running a small stabiliser mounting supply biz for go-kart folks for almost 8 years now. I’ve seen every hot mess on the track—from karts that wobble like a cheap phone on a wobbly table to ones that hug the curbs like they’re glued there, all because of a wonky stabiliser mounting. Today, I’m walking you through how to replace that part yourself, no fancy shop tools needed, and I’ll throw in some pro tips from my side as a supplier who’s spent more time with these mounts than I have with my morning coffee. Let’s dive in. Stabiliser Mounting

First off, let’s cut to the chase: why does this replacement even matter? A stabiliser (also called a sway bar, if you’re slangin’ around the track) does the heavy lifting when you’re turning hard—keeps your kart from leaning so much it flips, stops the back end from sliding out, and makes every input on the wheel feel responsive, not like you’re turning a rusty doorknob. The mounting is the core of that system—without a solid mount, the sway bar’s just a stick flopping around under your kart, doing nothing. I’ve had customers bring me karts in for tune-ups that skipped this swap, complaining of “that weird high-speed shake.” 9 times out of 10, the old mount was cracked, corroded, or stretched so bad it couldn’t hold the bar tight. And if you’re racing? Forget about it—half a second lost on every turn adds up over a race day, or worse, a crash waiting to happen.
Before you grab your wrench, let’s talk prep. You don’t need a full workshop, but there are a few non-negotiables. First, what kind of stabiliser mounting do you have? Most go-karts use either steel or aluminum mounts—steel’s cheaper, bends easy if you clip a curb, aluminum’s lighter, stronger, but more pricy. As a supplier, I’d tell you: match your new mount to the old one. Don’t go swapping steel for aluminum just to save weight if you’re a casual weekend racer—steel’s more forgiving for beginners. Next, tools: you’ll need a jack (or a set of jack stands—never work under a kart just on a jack, trust me), a socket set (metric is standard for most go-karts, but double-check your old bolts), a rubber mallet, some penetrating oil (WD-40 works, but PB Blaster’s better for stuck rusty bolts), a wire brush, and some anti-seize compound for the new bolts. Also, grab a rag to wipe up grease—your kart’s gonna be grimey, no way around it. Pro tip from my warehouse: mark which mount goes to which side (left vs right) with a Sharpie before you take anything apart. Mix up left and right mounts, and you’re gonna waste 20 minutes fixing a silly mistake.
Okay, let’s get to the actual replacement. First step: jack up your kart and secure it with jack stands. Slide under, find the sway bar—usually it’s a thin metal bar running across the bottom of the kart, connecting the two rear wheels. The mounts are the little brackets that hold the bar to the kart’s frame, usually one on each side, sometimes two on heavy-duty setups. Now, this is where the penetrating oil comes in. Spray it all over the old mount’s bolts and the bolts that hold the bar to the mount. Let it sit for 10 minutes—don’t skip this. I’ve had customers show up to my shop with stripped bolts because they tried yanking them out right away. Patience pays off here.
Next, loosen the mount bolts. Grab your socket, turn counterclockwise, and if it’s stuck, tap the end of the socket with your rubber mallet a few times—never use a steel hammer, that’ll round off the bolt head. Once the bolts are loose, take them out. Then, gently pull the old stabiliser mounting away from the frame. If the mount’s corroded, it might stick—tap it with the rubber mallet to loosen it, don’t yank hard, you don’t wanna damage the frame. Now, inspect the old mount: check for cracks, rust pitting, bent brackets, stretched bolt holes. If it’s any of those, it’s definitely time for a swap. I see a lot of beginners try to reuse cracked mounts because “they still look okay” but trust me, once a mount cracks, it’s only gonna get worse. Same with aluminum mounts—even a tiny bend here will throw off your sway bar alignment.
Now, prep the frame for the new mount. Grab your wire brush and scrub the area where the old mount was attached—get rid of all rust, dirt, old grease. If there’s any rust on the frame, a quick wipe with a little sandpaper works too. This step’s super important because if the new mount’s sitting on a crusty, dirty surface, it won’t seat right, and you’ll get wobble within a week. Wipe the area down with a rag to get all the brush dust off.
Time to install the new mount. First, line it up with the bolt holes on the frame. Double-check that it’s facing the right way (remember that Sharpie mark? Yeah, that’s why I told you to do that). Now, take your anti-seize compound and put a thin layer on the new bolts. This stops them from seizing up next time you need to swap. Insert the bolts through the mount and into the frame, then hand-tighten them just enough so the mount doesn’t move. Now, grab the sway bar: put it back into the mounts’ slots, make sure it’s sitting straight, not twisted. Now, tighten the mount bolts—here’s the key part: don’t crank them as tight as you can. Over-tightening will crack the mount, especially aluminum ones. Torque specs? Most hobby go-karts call for 25-35 ft-lbs, but if you don’t have a torque wrench, tighten them until the mount’s solid, no wiggle, and the bolt doesn’t turn anymore when you hold the socket. One quick check: push the sway bar side to side. There should be zero play—if there is, the mount’s either loose or not seated right. If that’s the case, loosen the bolts, adjust, and try again.
Wait, what about if your stabiliser is connected to the wheels? A lot of setups have little links (end links) that connect the sway bar to the rear wheel hubs. Once your mount is tight, reattach those end links, same process: hand-tighten first, then torque to spec. Don’t forget to check those end links too while you’re at it—if they’re worn, they’ll mess with the sway bar’s performance as much as a bad mount.
Now, test time. Lower your kart off the jack stands, take it for a slow test drive first. Go around a parking lot, make some sharp turns, feel for wobble. If it feels solid, great. If it still feels like it’s sliding or wobbly, pop it back up, check the mount bolts—they might not be tight enough. If everything’s good, you’re done.
But before I sign off, let’s hit a few pro tips that I live by as a stabiliser mounting supplier. First, replace your mounts every 20-30 race hours, or every year if you’re a casual driver, even if they look fine. Rust and wear sneak up on you. Second, if you’re racing, upgrade to a heavy-duty mount—they’re built to handle the constant curb clipping and hard turns. Third, don’t buy cheap no-name mounts. I’ve seen those $5 off-brand mounts break after one race. They’re thin steel, bad casting, won’t hold the sway bar tight. As a supplier, I stand by my stuff, and I tell all my customers: pay a little extra for quality, it saves you from crashes and replacements later.

If you’re not sure what kind of stabiliser mounting you need, or you need help picking the right one for your kart, hit me up. I’ve worked with every go-kart brand out there, from hobbyist models to race karts, and I can point you to the exact mount that fits your ride, no guesswork. Whether you’re swapping a worn mount for the first time or upgrading for better performance, I’ve got you covered. Don’t settle for a flimsy mount that’ll let you down—reach out, and we’ll make sure you get the right part, at a fair price, so your kart runs smooth on the track.
Engine Mount Reference:
Go-Kart Stability and Suspension Tuning, Kart Racing Technical Manual, 2021
Automotive Anti-Seize Application Guide, Performance Parts Association, 2022
Yuhuan Tongli Auto Parts Co., Ltd.
Yuhuan Tongli Auto Parts Co., Ltd. is one of the most experienced stabiliser mounting manufacturers and suppliers in China. With a professional production team, we are able to meet the needs of the majority of our customers. Please feel free to buy premium stabiliser mounting at competitive price from our factory.
Address: Wei Er Road, Automobile and Motorcycle Industrial Park, Yucheng Street, Yuhuan City, Zhejiang Province, China
E-mail: 13600574728@163.com
WebSite: https://www.tongliap.com/